raised platform handrail requirements

Fall Protection in General Industry - OSHAEmployers must take measures in their workplaces to prevent employees from falling off overhead platforms, elevated work stations or into holes in the floor and walls. To prevent employees from ... Provide a guardrail and toeboard around every open-sided platform, floor or runway that is 4 feet or higher off the ground or next level. Regardless of ... Other means of fall protection that may be required on certain jobs include safety harness and line, safety nets, stair railings and handrails.

General requirements. - 1926.451 | Occupational Safety and Health ...Exception to paragraph (b)(1): The requirement in paragraph (b)(1) to provide full planking or decking does not apply to platforms used solely as walkways or solely by employees performing scaffold erection or dismantling. In these situations, only the planking that the employer ..... Stairrail systems and handrails shall be surfaced to prevent injury to employees from punctures or lacerations, and to prevent snagging of clothing. 1926.451(e)(4)(v). The ends of stairrail systems and ...

Five Key OSHA Standards for Work Platforms - Spika Blog30 May 2017 ... The top edge height may exceed 45 inches (114 cm), provided the guardrail system meets all other criteria. Spika Work platform Mars Series. This may be the quintessential OSHA requirement for work platforms. Any work area four feet or more above the next level lower MUST have guardrails. Period. The guardrails must be on every open side of the platform, excluding openings. The only time railing is not required is when the platform is up against another vertical ...

Know the Requirements for General Industry -- Occupational Health ...1 Sep 2012 ... What can employers do to protect employees from falls at elevated heights? They can ... For general industry, the trigger height for providing fall protection is 4 feet (with exceptions for construction, scaffolding, fixed ladders, dangerous equipment, and utility work). Throughout its ... Under 1910.23(e)(1), OSHA says that a guardrail must have a vertical height of 42 inches nominal from the upper surface of the top rail to floor, platform, runway, or ramp level. "Nominal" ...

4. At vertical openings in the performance area of stages and ...At elevated walking surfaces appurtenant to stages and platforms for access to and utilization of special lighting or equipment. 6. Along vehicle service pits not ... Along alternating tread device, guards whose top rail also serves as a handrail, shall have height not less than 30 inches (762 mm) and not more than 34 ..... roof hatch openings and the top of the guard shall be located not less than 42 inches (1067 mm) above the elevated surface adjacent to the guard. The guard shall be ...

Ladders. - 1910.23 | Occupational Safety and Health AdministrationWhen the employer demonstrates that the requirement is not feasible, steeper slopes or vertical rung ladders may be used, provided the units are stabilized to prevent overturning;. 1910.23(e)(3)(ii). Mobile ladder stand platforms with a platform height of 4 to 10 feet (1.2 m to 3 m) have, in the platform area, handrails with a vertical height of at least 36 inches (91 cm) and midrails; and. 1910.23(e)(3)(iii). All ladder stand platforms with a platform height above 10 feet (3 m) have guardrails ...

PDS #075 - County of San DiegoGUARDS AND handrailS. BUILDING DIVISION. 5510 OVERLAND AVE., SUITE 110, SAN DIEGO, CA 92123 (858) 565-5920 (888) 336-7553. HTTP://WWW.SDCPDS.ORG. PDS 075 REV.: 1/01/2012. PAGE 1 of 2. GUARD requirements. Guards are required at the following locations per Section 1015 the 2016 California Building Code: Along open-sided walking surfaces, mezzanines, industrial equipment platforms, stairways, ramps and landings that are located more ...

California Code of Regulations, Title 8, Section 3210. Elevated ...(a) Buildings. Guardrails shall be provided on all open sides of unenclosed elevated work locations, such as: roof openings, open and glazed sides of landings, balconies or porches, platforms, runways, ramps, or working levels more than 30 inches above the floor, ground, or other working areas of a building as defined in Section 3207 of the General Industry Safety Orders. Where overhead clearance prohibits installation of a 42-inch guardrail, a lower rail or rails shall be installed.

Decking or other raised platform - The Scottish GovernmentPermitted development rights allow the erection, construction, maintenance, improvement or alteration of any deck or other raised platform within the curtilage of a dwellinghouse. In summary, the effect ... A building warrant from the local authority may be required for the deck or other raised platform, as explained in Section 2. Illustration ... (c) the combined height of the deck and any wall, fence, balustrade, handrail or other structure attached to it, would exceed 2.5 metres; or. (d) in the ...

Walking & Working Surfaces PPT - OSHAAn opening measuring 12 inches or more in its least dimension in a floor, platform, pavement, or yard, through which persons may fall. OSHA Office of Training and Education. 8. Guarding Floor Openings Definitions. Standard railing. Consists of top rail, mid rail, and posts. Height from the upper surface of top rail to floor level is 42 inches. Mid rail height is 21 inches. Standard toeboard. 4 inches high, with not more than ¼-inch clearance above the floor. OSHA Office of Training and ...

guardrails & handrails - Bremerton, WA28 Jan 2007 ... On the auditorium side of a stage, raised platform or other raised floor areas such as runways, ramps and side stages used for entertainment or presentation;. At vertical openings in the performance area of stages;. Along the side of an elevated walking surface when used for the normal functioning of special lighting or for access and use of other special equipment. Height. The top of guardrails shall be at least 42" in height. Exceptions: The top of guardrails for ...

Walking and Working Surfaces1 Oct 2009 ... devices so an employee can connect or disconnect while standing on ground, floors, or platform. Increase ladder widths to accommodate climbing devices. Do not use the reinforcing bar of fixed ladders as a rung or grab rail. ... Standard handrail. Securely mount a standard handrail on the wall or partition, enclosing the stairs. It must be between 30 and 37 inches high. Material and strength requirements must equal the stair railing. Mount the handrail with a minimum ...

04/17/2006 - Guardrail height requirements for construction activities ...17 Apr 2006 ... Answer: Yes, it would be a violation of Subpart M if construction work were performed on an elevated walking/working surface that is guarded by a permanent guardrail system with a 36-inch top rail, even though that top rail height is permitted for General Industry work ... (1) A standard railing shall consist of top rail, intermediate rail, and posts, and shall have a vertical height of 42 inches nominal from upper surface of top rail to floor, platform, runway, or ramp level.

Subpart D Walking-Working Surfaces - OSHAabove the height of the ladder. Guardrail system means a barrier erected along an unprotected or exposed side, edge, or other area of a walking-working surface to prevent employees from falling to a lower level. handrail means a rail used to provide employees with a handhold for support. Page 3. 3. Hoist area means any elevated access opening to a walking-working surface through ... platform means a walking-working surface that is elevated above the surrounding area. Portable ...

OSHA Publication 3124 - Stairways and LaddersRules for Stairways Stairways Used During Construction Temporary Stairs Stair Rails handrails Midrails Training requirements Glossary OSHA Assistance Safety and Health Program Management Guidelines State Programs Consultation Services Voluntary Protection ... T

Product Details

Product List