install wood over lath gate

Installing Wood Stripping Under a Tin Roof | Home Guides | SF GateUse a tool belt that has a hammer loop to hold nails, a measuring tape, chalk line and a hammer when installing the wood stripping. Experienced do-it-yourselfers can use a nail gun with 8d nail clips instead of a hammer and nails. When installing a metal roof over an existing roof, before installing the roofing, insulate the spaces between the wood strips with rigid insulation to prevent condensation. Cut the insulation to fit with a utility knife.

How to Remove Plaster From Walls to Convert to Drywall | Home ...Behind the plaster walls are narrow strips of wood called lath. The lath, nailed directly to the wall studs, ... ... Strike the top center of one of the walls with the hammer or crowbar, punching a hole through the plaster coating until you see the lath beneath. Insert the claw end of the crowbar into the hole and drag the claw through ... Most lath was installed in sections with dozens of strips secured to the same wall stud in the same area. Begin at the end of the strip for easier removal. The lath ...

Video: How to Install Floor Molding When Applying It to a Plaster ...installing floor molding when applying it to a plaster wall is going to require the use of a few key tools, like a level and something that you can use to make a straight line. install floor molding ...

How to Install Greenhouse Plastic | Home Guides | SF GateYou may also use staples as a fastener in lieu of nails and wood laths. Windy areas, however, may cause the staples to tear into the film over time. If you would like a removable option for the plastic, locking channels hold the film but provide you with a simple detachment mechanism that preserves the plastic's structural integrity.

How to Install Lighting in Plaster Ceilings | Home Guides | SF Gateinstalling a light in a plaster ceiling isn't much different than installing it in a drywall ceiling, except you must take extra care to keep the plaster from cracking. Plaster has a tendency to chip and crack as you cut through it, especially in older homes. The plaster is applied over thin wooden slats called the lath, and you must cut through both the plaster and the lath to install the light.

How to Plaster Internal Walls | Home Guides | SF GateAttach lath to it, then apply the three coats of plaster. This will give you

How to Install Childproof Gates on Plaster Walls | Home Guides | SF ...Mounting childproof gates onto plaster walls where there are no studs is problematic. ... The solution is to mount wooden strips onto the surface of the wall and attach the childproof gate to the wooden strips. ... 3. Position the wooden strips on the walls over the tape. Mark the tape at each hole in the strip. Remove the wooden strips. Drill through the tape and plaster at each mark with a masonry bit that is large enough to accommodate the diameter of the toggle on the toggle bolts.

How to Tile an Exterior Deck | Home Guides | SF Gateinstalling almost any type of tile is the same whether it's designed for the interior or exterior. ... With attention to a few key details, any do-it-yourselfer can install tiles over an exterior deck, be it wooden or concrete. ... Power washer; Roofing felt, 15-pound; Metal lath; Thinset rated for wet application; Latex additive; Notched trowel; Deck mud; 2-by-4-inch lumber; Waterproof, crack-isolation membrane; Waterproof exterior caulk; Chalk line tool; Level; Rubber mallet; Spacers; Wet saw ...

How to Attach Drywall to Plaster Walls | Home Guides | SF GateDrywall needs a sturdy substrate, so fasten loose plaster back to the wood lath strips behind it with plaster screws. Plaster screws have a washer-type ... If you are not comfortable working with electricity, hire an electrician to shut off the power before you begin working and to make necessary adjustments after you are finished installing the drywall. Some installers hang drywall without ... Consider the integrity of the plaster before hanging drywall over it. In most cases, plaster that is in ...

How Do I Anchor Shelves Into a Plaster Wall? | Home Guides | SF ...Plaster walls are made by nailing strips of narrow wood lath, spaced 1/4 inch apart, horizontally across the vertical studs. Plaster is then pressed onto the ... Repeat the process to install the remaining bracket(s) for each shelf, then mount the shelves to the brackets. 6. Back out the screw from the toggle bolt assembly and position the bracket over the hole, insert the screws through the bracket mounting holes into the toggle bolt assembly and tighten them. Continue with this process to ...

How to Create a Plaster Finish on Drywall | Home Guides | SF GateA panel of plasterboard went up in one piece, as opposed to installing wood wire mesh lath and then covering it with three coats of plaster. Drywall or ... Seal seams and corners of new drywall with drywall tape and joint compound -- at least two coats of compound over all tape -- and let it dry completely. Sand drywall that ... Put the bottom of the trowel on the compound and lift it to pull pieces up, then smooth the tops of the pull-ups with the straight edge for a stippled effect. Make partial ...

How to Apply Liquid Floor Leveler to Wood | Home Guides | SF GateWhen installing tile floors, you must ensure that the underlayment -- the surface the tiles will adhere to -- is perfectly level. Some homes ... install tile directly over the leveling compound once it has cured. ... Broom and dust pan; Vacuum cleaner; Sill seal; Staples; Staple gun; Caulking gun; Caulk; Paint tray; Paint roller and cover; Self-leveling primer; Expanded metal lath; Tin snips; Galvanized crown staples; Self-leveling compound; Electric drill; Mortar mixing attachment; Concrete float ...

How to Install an Electrical Box in a Lathe & Plaster Wall | Home ...Most homes constructed before World War II were built with plaster and lath walls, but few homes of that era have enough electrical receptacles for our modern times. Rather than ... Rather than removing large portions of plaster and lath to install modern electrical boxes, purchase a special type of box designed for old plaster and lath walls. This box, called an "old ... Place the front of the old-work electrical box on the wall and center the box over the 12-inch mark. D the contour of ...

How to Attach Paneling | Home Guides | SF GateWall paneling adds textural interest to a room. Whether you are going to attach paneling to an entire wall or just install wainscoting below a chair rail, the wood gives the room a different decorative touch. Adding wall paneling in an older home is a good option for covering cracked plaster-and-lath walls rather than repairing them. No matter what type of wall paneling you install, the process is similar.

How to Install Simulated Rock Siding | Home Guides | SF GateRock is not a popular house siding in areas where giant redwoods, magnificent firs and tall pines are readily available, but it is used in some places, either as full siding or as an accent to wood. ... ... Lay artificial stones on the lath with mortar, mixed in a large container with a prepared mixture; some masons put a "scratch" coat of mortar over the lath first to provide a better bond with mortar on the stones, while others put mortar on stones and set them into the lath. Follow ...

How to Attach Trim to Old Plaster Walls | Home Guides | SF GateThe best method for attaching trim to plaster walls is to secure the trim to the wood wall studs behind the plaster wall. The wood will readily grasp the finish ... If the nail goes through plaster or the underlying lathe, the nail will feel spongy when you strike it. When you strike the nail and the nail ... If you are installing crown molding to the ceiling, consider nailing 1-by-3-inch furring strips along the perimeter of the ceiling before adding the crown molding. The furring strips add more stability ...

Product Details

Product List