landscape timbers with pre drilled holes

How to Secure Landscape Railroad Ties | Home Guides | SF GateOld railroad ties are used in landscaping to provide edging for flower beds or walkways or to construct small retaining walls, compost bins or raised beds while also bringing an attractive rustic ... ... Drill holes through the top of the second course of timber, making sure that the holes are not in the same position as the spikes in the first row that are marked by the chalk. ... Stack additional rows of railroad ties, drilling holes and pounding spikes through, until the desired height is reached.

Treated landscape timbers: how to drill for the rebar spikes ...8 Apr 2014 ... Or drill for a snug fit and tap it through the wood? I wasn't sure if the landscape timber would split if I drove rebar through it. ... On top of the that the wood may shrink over time and will certainly change dimensions with the weather and the wood may split later without a hole slightly larger than the spike. You might look into the very long screws used to ... a smaller hole and having to whack it through. Attaching timbers on top of those, I'd use spikes and pre-drill them.

How To Install Landscape Timber Edging at The Home DepotLevel timbers and shim - landscape Timber Edging. As you layout timbers check that the course of timbers is roughly level. If necessary, shim the low ends with thin strips of wood. At corners, square the timbers with a framing square. 6. Use spikes to connect timbers. Use spikes connect timbers - landscape Timber Edging. Drill pilot holes slightly smaller than the diameter of a 10-inch spike at each end and every 4 feet along the second course. Drive a 10-inch spike into each hole with ...

Bespoke Timbers | A E Evans |All of our playground timbers, bespoke and landscape products are specially selected from sustainable sources, dried to reduce shaking (surface cracks) and pressure treated with TANALITH E following machining to meet the BS8417 standard. ... One of the benefits of supplying pre-drilled playground timbers is that the preservative treatment's integrity remains intact, further enhancing the service life of the product and eliminating the need for the customer or installer having to perform ...

Timbers - Kalamazoo Landscape SuppliesMake your first row straight and level. Stagger each row back 1". 5" x 5" or 6" x 6" timbers are good for most applications. Use 10" spikes or screws for 6" x 6" or larger timbers. Use 2 spikes or 4 screws per timber. pre-drill spike holes. Deadman should be 4' long, level into bank. If the wall butts up against the house, angle deadman away from house (weakest point). Place a deadman every 4 rows up minimum. Tack landscape fabric to back of wall if the soil is sandy. Take a close look at ...

How to Anchor Landscape Lumber | Home Guides | SF Gatelandscape lumber, more commonly referred to as landscape timber, is used to create structures within a landscape, including short retaining walls, steps and edging or raised beds. To ensure that any ... ... 3. Drill a pilot hole through the timber at each mark. ... 5. Mark the location of each rebar section and, in subsequent courses, spikes, on the face of the timber using chalk if you are going to stack and secure one or more rows of timber atop the first row.

Building Timber Landscape Steps - SULIS: Sustainable Urban ...Brace the back of each tie-back timber against a secure surface and drive two 10" spikes through the tread timber and into the tie-back timbers as shown below. These holes will need to be predrilled with 3/8&q

Securing landscape timbers | LawnSite15 May 2007 ... I'm installing timbers, 4"x6" as a border to contain mulch for a swingset/playground area. Any ideas to secure it to the ground? I was thinking of using 30" pieces of galvanized pipes sledgehammered through pre-drilled holes. My only concern with that is how to make the tops of the pipes kid friendly? They will be hammered flush. Any other ideas? mpm32, May 15, 2007.

landscape timber question | LawnSite24 Mar 2004 ... preferrably 24" rebar, but 18" will suffice. All other courses are secured with 8" timber screws. They cost a little more than 60d spikes (12"), but they more than make up for it in the amount of time spent driving them. If you use spikes, you need to drill a 3/8" hole through both timbers before you drive the spike, or else the spike will tend to wander out the front or back of the timber following the grain... FWIW, I try not to use timbers at all. Compared to pre-cast block, they ...

What Kind of Nails or Spikes for Landscaping Timber? | Hunker11 Jun 2011 ... Rebar (reinforcing bar) is commonly used to reinforce concrete during construction projects, but also works well to secure landscape timbers together. The timbers are held in place by pounding the rebar through predrilled holes and into the ground at an angle. In a single row they can then serve as edging to hold bricks or stones in place for walkways or patios. By securing several rows of timbers together with the rebar, and pounding it into the ground at least 12 ...

How to Build a Timber Retaining Wall - Landscaping, Lawns & Ponds7 Jul 2011 ... The nails also had to be pre-drilled. By using timber wall screws you won't need to pre-drill any holes and you won't shift the wall around pounding in the nails. 1. Set up wooden stakes and Mason's strings to represent the height and perimeter of the retaining wall. 2. Stretch another level line near ground to represent the top of the first course of landscaping timbers. 3. Dig a 12-inch-deep trench around perimeter of retaining wall. 4. Use a hand tamper to compact the ...

What Kind of Nails or Spikes for Landscaping Timber? - Home Guideslandscape Spikes. Galvanized landscape spikes look like extremely large nails. They work well when you need to secure stacked timbers to one another, such as when you are building a raised bed, a sandbox, or a retaining wall. Spikes come in lengths between 8 and 14 inches. You don't need to pre-drill holes for these fasteners, but they are effective only for holding timbers together. landscape spikes aren't effective for keeping timbers attached to the ground.

Building a Timber Retaining Wall | how-tos | DIYpre-drill holes for the spikes about every 8 inches. Secure this second row to the foundation row with 60d spikes, using the pre-drilled holes. Build the next row, remembering to stagger the timbers. Again, attach each row to the row below it using 60d spikes (image 1). Use a hand saw to cut off any excess in order to make the ends of the wall even (image 2). Repeat the process, building subsequent rows and offsetting the timbers so that the ends of every row are in alignment (image 3) ...

Product Details

Product List