how to secure a deck to cement blocks

Cinder Block Fasteners | CONFAST23 Sep 2011 ... View detailed information about cinder block fasteners where to purchase and how to install.

How to Attach Joists to a Cinder Block Wall | Home Guides | SF GateJoists sit horizontally on edge on cinder block, cl space foundations or basement walls to support the floors of a home. You can use engineered I-beam trusses as joists or choose to use 2-by-12 or ...

Decks.com. Ledger Board Attachment to a Solid Concrete ...11 Jun 2016 ... Now you can drill the holes through the wall into the basement or cl space using a hammer drill with a masonry bit. Then just line up the board to the holes in the brick and screw in the fasteners. When attaching to solid masonry you will have to install expansion anchors with a minimum diameter of ½ and set into the wall at least 2-1/2. Hollow concrete block can easily break when drilled and doesn't leave adequate bearing support for anchors. If you are attaching ...

Ultimate Deck Build 2015: Fastening a Ledger to Concrete - Fine ...6 Jan 2015 ... On this project, the 2×10 joists of the main deck frame sit just about even with the top of the foundation, and a landing framed with 2x8s sits atop the main frame, serving as a tran

How to Safely Attach a Deck to a House - This Old House - YouTube1 Jun 2014 ... This Old House general contractor tom Silva shows how to save a wood deck from a catastrophic collapse. Click here ... and if it is a masonry or stucco house the deck must be free standing meaning you have to install support posts under the side of the deck that is against the house as well, including footers. It can be ... I've never heard of using red head concrete anchors to attach a deck horizontally to a house, they're usually used for attaching post bases to footers..

How to Attach a Ledger to a Cinder Block | eHowBuilders use ledger boards to attach one structure to another. Typically made of two-by lumber, ledger boards attach horizontally to an existing structure, such as a house or garage, and are used to join a deck, roof or other add-on to the original structure. Successfully attaching a ledger to a cinder block can be accomplished by using the right hardware. Things You'll Need. Drill. 1/4-inch wood bit. Countersink bit. Tape measure. Level. 3/16-inch mason's bit. Masking tape. 2-1/2-inch ...

joists - Can I attach a freestanding deck to concrete block garage ...The fact is that your deck's weight load must be carried underneath it and not using the cinder blocks supporting your garage. That does not limit you from attaching it to the garage to provide horizontal stability and to keep movements in unison. You would simply need to bolt in a faux ledger to the cinder blocks. Make sure that you have at least two posts close to the garage that you are showing as the weight bearing points for that wall. any good inspector should ...

How to Choose and Use Concrete Fasteners, Masonry Screws ...Learn how to install light-duty, medium-duty, heavy-duty fasteners and masonry screws. ... Best uses: Concrete, concrete block, mortar and brick. how to use: Hold your wood or other material in position and drill through it into the concrete to the correct depth. Slip in the anchor (Photo 3). to finish the job, strike the exposed pin with ... These anchors in the large 3/8-in. to 1/2-in. dia. versions are perfect for anchoring heavy, weight-bearing framing members such as deck ledger boards.

How to Attach Floor Joists to a Concrete Block House - Home GuidesWith most concrete block construction, blocks comprise the outer walls of a house, and floor joists for the main and upper floor attach between the walls. The primary components are ledgers, also known as rim joists, that attach at opposite walls with anchor bolts. Joist hangers attach to the ledgers and support the ends of the floor joists. Consult the local building department regarding the size of the ledger and joists, as well as the spacing of joist hangers. Typically, 5/8-inch diameter ...

Masonry anchors for brick, cinderblock and cement - YouTube24 Jan 2013 ... Would you have a recommendation for securing a metal door jamb in cinder block for maximum strength/security (renovation). The block is hollow, about 3/4" or 1" I suppose, with no solid sections because the block is edge on, surrounding the jamb. Ideal would be to fill the concrete block, which may happen later, but it's 20 degrees out now and concrete will freeze. So it's tricky because there's only the thickness of the cinder block to work with. I'm thinking maybe ...

Ledgers on Challenging Walls | Professional Deck Builder ...1 Sep 2007 ... Readers of this magazine likely know how to safely secure a deck ledger to most houses. ... The anchor spacing would be as shown at right in the table "Ledger Fastener Spacing for Masonry Walls." Figure 1. In most cases, deck ledgers can be bolted directly to poured concrete or concrete block walls. Expansion anchors never lead shields are used in solid masonry or filled block, and approved epoxy or acrylic anchors and bolts are used in hollow masonry.

Product Details

Product List